Risultati da 1 a 9 di 9

Discussione: Line-based edge-picking family?

  1. #1
    Senior Member L'avatar di PatrickGSR94
    Data Registrazione
    July 7, 2017
    LocalitÓ
    Hernando, MS
    Messaggi
    522
    Ora locale
    05:17 AM

    Not allowed! Not allowed!

    Line-based edge-picking family?

    Is it possible to create a line-based family that is placed by picking a 3D edge in a 3D view, and the host will be that edge and not some horizontal work plane or level? It almost needs to be like a combination face/line hosted family.

    One use would be for things like roof ridge vents, or hip/ridge tiles for a tile roof.
    Ultima modifica di PatrickGSR94; July 17th, 2018 alle 08:53 PM

  2. #2
    Senior Member
    Data Registrazione
    August 19, 2011
    LocalitÓ
    New Hampshire
    Messaggi
    506
    Ora locale
    05:17 AM

    Not allowed! Not allowed!
    If you set your workplane to the surface you're adding the family to, you can draw on that line. I'm fairly sure choosing it as the host is impossible.

  3. #3
    Forum Co-Founder L'avatar di Twiceroadsfool
    Data Registrazione
    December 7, 2010
    LocalitÓ
    Dallas, TX
    Messaggi
    10,573
    Ora locale
    04:17 AM

    Not allowed! Not allowed!
    Line Based Generic Models CAN use Pick Lines, to select an Edge. But the workplane WILL be one of the two faces of the roof, and it will orient it self as such. Only way around that is adaptive components, per (perhaps) a structural framing family. But... yuck, on both counts.

    I just make my Ridge Vents modeled off one plane of the roof (as the LBGM) and they work great.

  4. #4
    Senior Member L'avatar di PatrickGSR94
    Data Registrazione
    July 7, 2017
    LocalitÓ
    Hernando, MS
    Messaggi
    522
    Ora locale
    05:17 AM

    Not allowed! Not allowed!
    Yep I noticed that behavior of the tilted ridge vent.

    Another thing I wanted to make was a line-based family for those RainhandleR rain dispersion louvers, which have little brackets every so often, and then 6 louver blades running continuous long the roof. I succeeded in making a railing family that works pretty well, and I can pick my roof fascia trim if I have a level datum in that spot. But I'd rather have an actual family that can be saved and loaded instead of a system family, and picking the edge in 3D is so much easier than trying to draw it in plan or elevation, picking a work plane, blah blah blah, especially when there are many of them around a roof.

    Another thought: what about nesting a line-based family into a face-based family???

  5. #5
    Forum Co-Founder L'avatar di Twiceroadsfool
    Data Registrazione
    December 7, 2010
    LocalitÓ
    Dallas, TX
    Messaggi
    10,573
    Ora locale
    04:17 AM

    Not allowed! Not allowed!
    Doesnt work that way. Besides: A LB family is already a Face Based Family.

    Honestly, i have some LB Louvers, and i dont like them. Id rather completely unhosted or Face Based and stretchable. The User Experience on the Line Based ones isnt that awesome. For Ridge Vents, all day long. Louvers, i wouldnt do it.

  6. #6
    Forum Addict L'avatar di elton williams
    Data Registrazione
    December 7, 2010
    LocalitÓ
    Gold Coast
    Messaggi
    2,675
    Ora locale
    08:17 PM

    Not allowed! Not allowed!
    Agreed regarding louvres. Also, LB families have that habit of auto-joining in line and at corners precisely when you don't want them to - and there's no option to disallow joins like you can with say, walls.

  7. #7
    Senior Member L'avatar di PatrickGSR94
    Data Registrazione
    July 7, 2017
    LocalitÓ
    Hernando, MS
    Messaggi
    522
    Ora locale
    05:17 AM

    Not allowed! Not allowed!
    These aren't "louvers" like you normally think of louvers in a wall, they're a gutter replacement product. So they run along the edge of a roof eave/fascia. Instead of a single metal profile like a normal roof gutter, they're small brackets spaced out with 6 little metal strips running along the length to create a "gutter" that disperses rainwater evenly instead of it just spilling off the roof. I used to use a solid profile that was the shape of the bracket to represent the product, but it never looked right. Making them as a railing makes it look right, it's just not the most user friendly or the easiest to load into other projects.

    Anteprime Allegate Anteprime Allegate Rainhandler.JPG‎  
    Ultima modifica di PatrickGSR94; July 18th, 2018 alle 09:46 PM

  8. #8
    Forum Co-Founder L'avatar di Twiceroadsfool
    Data Registrazione
    December 7, 2010
    LocalitÓ
    Dallas, TX
    Messaggi
    10,573
    Ora locale
    04:17 AM

    Not allowed! Not allowed!
    Yeah, i would do those as Face Based (non line based) families.

  9. #9
    Forum Addict L'avatar di GMcDowellJr
    Data Registrazione
    December 21, 2010
    LocalitÓ
    Phoenix, AZ
    Messaggi
    2,667
    Ora locale
    03:17 AM

    Not allowed! Not allowed!
    If a profile could have multiple loops, that would work as a fascia, I bet.

Discussioni Simili

  1. Edge based family + schedule possible???
    Di martian75 nel forum Architecture and General Revit Questions
    Risposte: 2
    Ultimo Messaggio: April 30th, 2016, 09:35 PM
  2. Locking the origin of a line based family in the host family
    Di Karzan nel forum Architecture - Family Creation
    Risposte: 2
    Ultimo Messaggio: April 1st, 2015, 10:30 PM
  3. Line Based Family nested inside another line based family and arrayed
    Di MadMatt nel forum Architecture - Family Creation
    Risposte: 3
    Ultimo Messaggio: January 6th, 2013, 06:29 PM
  4. Array a line based family inside another line based family
    Di MadMatt nel forum Architecture - Family Creation
    Risposte: 5
    Ultimo Messaggio: December 11th, 2012, 02:08 PM
  5. Line Based Family Help
    Di dzatto nel forum Architecture - Family Creation
    Risposte: 20
    Ultimo Messaggio: February 1st, 2012, 01:04 AM

Permessi di Scrittura

  • Tu non puoi inviare nuove discussioni
  • Tu non puoi inviare risposte
  • Tu non puoi inviare allegati
  • Tu non puoi modificare i tuoi messaggi
  •