Risultati da 1 a 5 di 5

Discussione: sloped wall joined to sloped roof

  1. #1
    Junior Member
    Data Registrazione
    May 11, 2012
    Messaggi
    30
    Ora locale
    01:22 AM

    Not allowed! Not allowed!

    sloped wall joined to sloped roof

    Ok, so here is my conceptual mass that I used to generate the walls (by face) and roof (which is actually a wall)

    Clicca sull'immagine per ingrandirla

Nome: Screen Shot 2016-05-13 at 17.47.03.png
Visite: 23
Dimensione: 187.2 KB
ID: 26675

    Works fine for the most part with wall by face, and i've sorted out the joints for the most part, but here revit does somthing weird, how do I make the roof's end flush with the wall?

    Clicca sull'immagine per ingrandirla

Nome: Screen Shot 2016-05-13 at 17.47.22.png
Visite: 24
Dimensione: 150.1 KB
ID: 26676

    And that diagonal line looks hideous, I can't seem to alter the wall joints here, any tips? should I construct this a different way?
    Ultima modifica di sohn; May 13th, 2016 alle 04:05 PM

  2. #2
    Junior Member
    Data Registrazione
    May 11, 2012
    Messaggi
    30
    Ora locale
    01:22 AM

    Not allowed! Not allowed!
    Oh, and here is a section of the roof

    Clicca sull'immagine per ingrandirla

Nome: Screen Shot 2016-05-13 at 18.01.38.png
Visite: 15
Dimensione: 116.5 KB
ID: 26677

  3. #3
    Forum Addict L'avatar di elton williams
    Data Registrazione
    December 7, 2010
    LocalitÓ
    Gold Coast
    Messaggi
    2,665
    Ora locale
    11:22 AM

    Not allowed! Not allowed!
    Citazione Originariamente Scritto da sohn Visualizza Messaggio
    Ok, so here is my conceptual mass that I used to generate the walls (by face) and roof (which is actually a wall)

    Clicca sull'immagine per ingrandirla

Nome: Screen Shot 2016-05-13 at 17.47.03.png
Visite: 23
Dimensione: 187.2 KB
ID: 26675

    Works fine for the most part with wall by face, and i've sorted out the joints for the most part, but here revit does somthing weird, how do I make the roof's end flush with the wall?

    Clicca sull'immagine per ingrandirla

Nome: Screen Shot 2016-05-13 at 17.47.22.png
Visite: 24
Dimensione: 150.1 KB
ID: 26676

    And that diagonal line looks hideous, I can't seem to alter the wall joints here, any tips? should I construct this a different way?
    Im only on my phone so the images are a bit hard to see. Im guessing "And that diagonal line looks hideous.." you mean the mitred condition between roof and wall? Seeing as you used walls for thw roof can you join geometry to hide the join? If you want a separate butt joint (beam on post) look maybe create the roof from a new mass surface which encompasses the full extenet. Or just use a system roof family outside the massing family.

  4. #4
    Junior Member
    Data Registrazione
    May 11, 2012
    Messaggi
    30
    Ora locale
    01:22 AM

    Not allowed! Not allowed!
    Citazione Originariamente Scritto da elton williams Visualizza Messaggio
    Im only on my phone so the images are a bit hard to see. Im guessing "And that diagonal line looks hideous.." you mean the mitred condition between roof and wall? Seeing as you used walls for thw roof can you join geometry to hide the join? If you want a separate butt joint (beam on post) look maybe create the roof from a new mass surface which encompasses the full extenet. Or just use a system roof family outside the massing family.
    Clicca sull'immagine per ingrandirla

Nome: Screen Shot 2016-05-14 at 10.43.54.png
Visite: 12
Dimensione: 492.3 KB
ID: 26679

    Yes, it's the mitred join, i can't seem to grab the joint with the wall joins tool (works only in plan view?), joining does not help either. I remade the wall and roof using the in-place component tool, that way I could make a clean joint, however the walls are dumb now, no layers within the wall. And mostly irritating is that I can't re-align the pattern (panels) without moving the whole object, as if the pattern i stuck!

    Not sure how to apply your suggestions? I tried the roof tool, same thing there, the ends are squared, and not in flush with the wall angle.
    Ultima modifica di sohn; May 14th, 2016 alle 11:00 AM

  5. #5
    Forum Addict L'avatar di elton williams
    Data Registrazione
    December 7, 2010
    LocalitÓ
    Gold Coast
    Messaggi
    2,665
    Ora locale
    11:22 AM

    Not allowed! Not allowed!
    Yes the wall joins tool will only work in plan.
    If you go back into edit mode the surface pattern lines should move on their own.
    I realise now you want the whole piece of geometry to be clean single item. The only other thing i can think of right now while having a few saturday night brewskies would be to make the whole thing as roof by extrusion where you can actually use layers and keep it (relatively) parametric
    https://knowledge.autodesk.com/suppo...F9953-htm.html
    Ultima modifica di elton williams; May 14th, 2016 alle 11:14 AM

Discussioni Simili

  1. Flat Pad on Sloped Roof
    Di B Arch nel forum Architecture and General Revit Questions
    Risposte: 8
    Ultimo Messaggio: November 23rd, 2015, 09:36 PM
  2. sloped roof modeling
    Di mona miller nel forum Architecture and General Revit Questions
    Risposte: 10
    Ultimo Messaggio: May 18th, 2014, 01:15 AM
  3. Sloped glazing in sloped wall
    Di stl4310 nel forum Architecture and General Revit Questions
    Risposte: 25
    Ultimo Messaggio: September 7th, 2012, 08:12 PM
  4. Sloped roof
    Di theshell07 nel forum Architecture and General Revit Questions
    Risposte: 3
    Ultimo Messaggio: March 13th, 2012, 04:40 PM
  5. handrail on sloped roof
    Di Povilas nel forum Architecture and General Revit Questions
    Risposte: 4
    Ultimo Messaggio: February 27th, 2012, 08:05 AM

Tag per Questa Discussione

Permessi di Scrittura

  • Tu non puoi inviare nuove discussioni
  • Tu non puoi inviare risposte
  • Tu non puoi inviare allegati
  • Tu non puoi modificare i tuoi messaggi
  •