Search:

Type: Posts; User: GMcDowellJr

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    17
    Views
    549

    Imastealthat

    Imastealthat
  2. Replies
    17
    Views
    549

    Do they raise (or try) their fee after hearing...

    Do they raise (or try) their fee after hearing this?
  3. Replies
    17
    Views
    549

    Imagine that.

    Imagine that.
  4. or all categories on a specific workset (assuming...

    or all categories on a specific workset (assuming your links on their own workset)
  5. Put it in your BIMxP that they need to turn it...

    Put it in your BIMxP that they need to turn it back to black before they send it over? ;)

    I think a filter is your only solution if you're not going to edit the model.
  6. Perhaps it's unhosted... or, more likely, ceiling...

    Perhaps it's unhosted... or, more likely, ceiling hosted. Edit the family. If you see a host you can tell what it's looking for. If there's not host then it's unhosted.
  7. Except perhaps in model groups where face-based...

    Except perhaps in model groups where face-based families have been known to, sadly, cause issues.
  8. Can that Dynamo graph reach into the families to...

    Can that Dynamo graph reach into the families to make changes or is it just what's editable in the active project? If the former that's the bomb.com!
  9. Check out Ideate’s Style Manager. It’s a little...

    Check out Ideate’s Style Manager. It’s a little pricey but it makes short work of this. Get you down to one subcategory in no time.

    The SNF is the way to go.


    Sent from my iPad using Tapatalk
  10. Replies
    6
    Views
    1,198

    a slab edge is part of a floor... expand floors

    a slab edge is part of a floor... expand floors
  11. Replies
    21
    Views
    5,881

    Didn't know about the sublet/subleased/etc. That...

    Didn't know about the sublet/subleased/etc. That could bite you in the butt regardless of what the license owner says... actually, it'd probably get them in trouble rather than you for allowing you...
  12. Replies
    6
    Views
    1,198

    be aware that how it's been joined with other...

    be aware that how it's been joined with other geometry will affect the result
  13. Replies
    21
    Views
    5,881

    What I was assuming as well. I doubt Autodesk...

    What I was assuming as well. I doubt Autodesk could do anything about it other than report it to the license owner.
  14. Replies
    21
    Views
    5,881

    Well then... sounds like you have your answer! ...

    Well then... sounds like you have your answer!

    Of course you should really consult a lawyer for actionable legal advice. ;)
  15. Replies
    21
    Views
    5,881

    I'm gonna bet that, since the license belongs to...

    I'm gonna bet that, since the license belongs to company A, it can't (legally) be used for work with company B.
  16. Replies
    9
    Views
    1,034

    I think it's a question of where you want to put...

    I think it's a question of where you want to put your modeling time. You can have one wall with an edited profile. Or multiple walls, one or more per floor, that you keep aligned vertically. Pick...
  17. Replies
    13
    Views
    501

    Every point that bounds the plane needs to be...

    Every point that bounds the plane needs to be modified to as many decimals as you can manage (Revit stops at the 12th or 13th I believe) relative to the slope. I use Dynamo to pull the length of a...
  18. Replies
    19
    Views
    16,358

    the setup is right... but is the line pattern...

    the setup is right... but is the line pattern really a centerline and is the the centerline pattern appropriate of the for the scale/length of witness line?
  19. Replies
    19
    Views
    16,358

    The dimension style needs to be setup correctly...

    The dimension style needs to be setup correctly as well. You can change the centerline symbol, pattern, and tick mark.
  20. Replies
    13
    Views
    1,679

    1 - Depends on how much they're likely to move...

    1 - Depends on how much they're likely to move around. If you document out a design live in the model and then it moves you're likely going to have to document it again. Living outside of the live...
  21. Replies
    15
    Views
    1,669

    You mean angled in elevation, yes?

    You mean angled in elevation, yes?
  22. Replies
    23
    Views
    2,761

    Cause they blow in model groups.

    Cause they blow in model groups.
  23. This is the weirdest thing and must have...

    This is the weirdest thing and must have something to do with changing the Group Types at the API level.

    Here's what works. Instead of making one duplicate and applying it to all but one, it now...
  24. 2 Group Types with Different Parameters?

    How can this be possible... I have 2 groups (more actually but let's just focus on these 2) that are the same group type with instance parameters set to not vary by group type and yet the values...
  25. And this is why I welcome our robot overlords......

    And this is why I welcome our robot overlords... they do the bring things better and faster leaving me time to do the fun creative stuff! ;)
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4